Compressed air is a low efficiency media, and is thus very expensive to produce. This thesis work began by mind mapping how to create savings on the compressed air system at Billerud Skärblacka AB. Certain issues have been chosen for further studies.In order to identify the consumption of compressed air at PM 8 and 9, several measurements were made. At PM 8 there were not found any pressure drop, only large pressure variations for short periods of time. The causes of these pressure variations were not established.

Mammary gland neoplasia is one of the most common diseases in the bitch and the most common neoplastic disease. More than 13 % of the female dog population in Sweden suffers from mammary tumors during their lifetime. The disease can affect bitches in all ages but most often middle aged and older dogs. Some breeds such as Poodle and English Setter are predisposed for the disease. The aim of this study was to evaluate if it is possible to improve the post surgical healing process by using a pressure pad.

An automatic control system for calibration of pressure indicators has been constructed. This control system can be used as a complement to the calibration system located at AerotechTelub, division MainPartner, in Linköping. The calibration system used today contains some not wanted pressure changes, which is compensated by hand today. The new system presented in this report automates the calibrating process and simplifies the calibration. Suitable hardware as motor, controls card and so on have been found and software in the form of Visual Basic program has been developed.

In this essay, I investigate Swedish possibilities to influence the Common Agricultural Policy of the European Union (CAP). After having summarized my findings, I try to explain the structure of influence by using Multi-level governance theory.Ten years have passed since Sweden joined the Union, and many changes have followed in the agricultural sector. By investigating the small country of Sweden's possibilities to influence CAP, I hope to be able to get a notion of the possibilities to influence the EU in general. The essay examines four possible paths for agricultural interests to influence the policy process in Brussels:* Through elected representatives of Sweden in the European Parliament, the Council of Ministers and in the Swedish Parliament* Through subnational institutions, such as the local authorities and regional representatives.* Through the Swedish Agricultural Office* Through the Swedish pressure group within the agricultural area, LRFThese four groups all have very different channels to the policy process on agricultural issues. The differences are mostly in terms of decisive power or advisory power and institutional contacts or lobby contacts.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

The running of gas turbines with low emissions causes high pressure pulsations to arise in the combustion chamber. These pulsations are high amplitude sound vibrations. At some frequencies these are harmful to the gas turbine. Hence these pulsations are monitored to avoid operating conditions where pulsations are specifically harmful. It is necessary to expose the system of known pulsations to verify the functionality of the monitoring process.

In Sweden approximately ten percent of all children grows up in a family where at least one parent is having an alcohol related addiction. Since 1998 the development of group activities for children in this situation has been immense. The aim of group activities is to break the child's isolation and make them feel that they are not lonely in their experiences, give them knowledge about addiction and relive the pressure of guilt and responsibility.In a comparative study we examined studied how two different group activity models one with the conception of illness and one without, use the children's network to support the group process. The aim was also to find each models definition of the "normal family", since we understood the groupactivity as a part in the normalization process. We reached our aim through interviews with group leaders and by literature studies.

In offshore oil production FMC Subsea systems use a product called cap. The cap´s mainly task is to protect hubface and seal areas on inboard hub against dirt, corrosion and mechanical damage under installation of a subsea system. A new model of a cap has been designed and analysed using finite element method. The model is called KC3-12 and has a new function, emergency release, which is a backup method for the ROV (remote operated vehicle) to release the cap from the hubface when it is placed under water. The cap KC3-12 was found to fulfil the criteria under the test load pressure, according to ASME VIII, div2.

The task of this project was to build an computer processing system for pressureregulation, in which the pressure loss over the open hydrolicvalve should be kept as low as possible. By using an cross connected proportional directional valve the valve problem could be solved. The control- and regulationproblem for the pressureregulation system was solved by using the DAQ- card NI6035E from National Instruments and the computerprogram Automatic Pressure Control 1.0 which has been software developed and written in Visual Basic. The final result showed that correct processvarible was obtained in 0,5 seconds, when the setpoint was changed in the testarea 0 - 2,5 MPa..

Due to higher standards of living around the world, greater industries and larger infrastructures causes an increase of the global energy consumption. This harvest of energy puts a great stress on the global environment. With this development, it becomes increasingly important to utilize energy resources in the best possible way.Fans are components that are often used in the industry and in households. A common problem is that the fan is oversized. An oversized fan causes an excessive flow, which has to be adjusted in order to achieve the correct flow.

This thesis work has been performed at the department of diagnosis and dependability at Volvo Car Company, Torslanda. The background of this project is based on interest in ascertaining how different factors possibly can affect a diagnosis method, which has been developed to find leaks in the fuel tank and evaporation system. According to the OBD II requirements leaks with an orifice diameter larger or equal to 0,5 mm, must be detected. The idea of the diagnosis method is to create an over pressure in the system with an air-pump. The current through the pump is measured and correlates to the power consumed by the pump.

The Homogeneous Charge Compression Ignition (HCCI) engine is promising in terms of lowNOx, low particulates and high efficiency. Due to its homogeneous charge, where thecombustion starts almost simultaneously from a number of points in the combustion chamber,only lean mixtures are possible to burn because of the resulting rapid combustion, which is muchfaster than the combustion in an SI-engine or a diesel engine. When richer mixtures are used thecombustion will start earlier and also be more violent.To phase the combustion later and lower the combustion speed, external cooled EGR can beused. The EGR-system used in this thesis uses a divided exhaust channel where one channel andits corresponding valve are used only for transporting EGR back to the intake system.Consequently the EGR-valve is connected to the intake pressure. This system is called Direct-EGR (D-EGR).Engine tests verified that the CA50 indeed is phased later when cooled EGR is used.

Background: Pressure ulcers are a common problem and cause great suffering for those who develop it, and are also an expensive cost to the society. Aim: To describe nursing measures for prevention of pressure ulcers among elderly people in ordinary and nursing homes. Method: A literature review by structured analyze of scientific articles. Result: The analyze resulted in six subjects for prevention of pressure ulcers. These subjects were; risk assesment, nutrition, repositioning, skin/hygiene, nurse knowledge and documentation.

Prostate cancer is the most common cancer in men. One type of treatment is internal radiation therapy, brachytherapy. This treatment requires the patient to lie completely motionless and in lithotomy position. The purpose of this study was to investigate the prevalence of pressure ulcers associated with brachytherapy in prostate cancer at the UniversityHospitalin Uppsala. Furthermore, the purpose was to identify the most common location of pressure ulcer and to examine whether there were any connection between risk factors and possible pressure ulcers.

Volvo Construction Equipment is a world leading company in construction machinery. Tomaintain the best products, development is prioritized. The master thesis regards sound reductionof the hydraulic system on a wheel loader. The background to the master thesis is asimulation made on the hydraulic system, performed autumn 2005. The result of the simulationshows that the energy of the pressure ripple is reduced when the paralleled hydraulicpumps are phase shifted and reduces each others pump pulsations.